How To Use Penis Extenders
A penis extender is a device composed of a plastic ring
base, two metal rods with internal springs, and a plastic
structure with a silicone band. The plastic pieces are made
of POM (a synthetic material that will not be affected by
combustible fluids such as alcohol) . The band is made of
medical grade silicone or latex. The metal rods are made of
tin covered by a thin layer of nickel. The springs are made
of stainless steel and the axes are made of surgical
aluminum.
It is mainly used for penile lengthening traction ,
correction of penile curvatures without surgery (Peyronies
Disease) and post penile lengthening surgery and after
plastic and reconstructive surgery of the penis. It is
now also used as a stand alone method of increasing your
penis size by using the principle of traction.
With a measure tape, first measure the length and perimeter
of the penis in flaccid state.
The initial size of the penis extender is usually around
9 cm (3.6 inches) and is measured from the lower part of the
plastic ring to the upper part of the metal axis. Calculate
the personal size of your device by taking away 4 cm (1.6
inches) from the size of your penis when erect. If you have
a curved or deviated penis subtract 5 cm (2 inches) to
calculate your personal size.
Example 15.7 cm - 4 cm = 11.7 cm for your starting size.
Now prepare the device so that it corresponds to the
personal size you have calculated. First, detach the upper
plastic support by lifting it upwards. After that, add so
many pieces as needed to reach the personal size of your
penis extender device.
If the personal size of the device is smaller than the
initial size, then start the treatment with the initial size
of the penis extender device.
|
Adaptation Period |
|
Days |
Extender
Size |
Hours Per
Day |
| 1 - 5 |
Start with personal size of the
extender |
3 |
| 6 - 10 |
On day 6 add one piece of 0.5cm
on each side |
6 |
| 11 - 15 |
On day 11 add one piece
0.5cm on each side |
8 |
As soon as the adaptation period is over, you can switch
over to standard mode or special mode. You can also switch
between the two from time to time.
Standard mode : add one piece on each side every 7
days. (recommended) and wear 9 hours per day
Special mode : add one piece on each side every 3
days and wear 4 hours per day.
Take breaks for as long as you consider necessary and
massage your penis. As soon as you have 4 small pieces of
0.5cm attached to each other you can replace them by medium
part of 2 cm.
From the third month on, you need to increase the size of
the penis extender more slowly. Please add a small piece
0.5cm on each side only every two weeks.
USE PENIS EXTENDERS WITH PATIENCE
Be patient and consistent with its use. This is the ONLY
way to obtain your goals. The first day. put on and take the
device of 10 times in the day.
Every 2 hours you will need to remove it and let the tissues
relax for a few minutes. Rest periods are mandatory. In the
advanced stages you must rest every hour or hour and a half.
Apply a massage to your penis during the breaks.
It is advisable that the device should be worn folded
upwards, behind the zipper area. Wear comfortable, loose
fitting underwear and pants. The device must be cleaned with
a neutral soap and water every 4 days.
If you do not wear the device for 15 to 30 days, begin
treatment at 1 cm less than the size of the device at that
time. After 5 days, increase of 0.5cm and repeat the
increment of 0.5cm in 5 more days. after this 10 day
adaptation period resume with the chosen mode.
Diabetics must get approval from their physician and
the use of the penis extender must be controlled. There are
no side effects as long as you follow the instructions. |
